MAN page from CentOS 8 pciutils-3.6.4-2.el8.x86_64.rpm
Section: The PCI Utilities (8)
Updated: 25 January 2020Index
setpci - configure PCI devices
setpciis a utility for querying and configuring PCI devices.
All numbers are entered in hexadecimal notation.
Root privileges are necessary for almost all operations, excluding readsof the standard header of the configuration space on some operating systems.Please seelspci(8)for details on access rights.
- Tellssetpcito be verbose and display detailed information about configuration space accesses.
- Tellssetpcinot to complain when there's nothing to do (when no devices are selected).This option is intended for use in widely-distributed configuration scriptswhere it's uncertain whether the device in question is present in the machineor not.
- `Demo mode' -- don't write anything to the configuration registers.It's useful to trysetpci -vDto verify that your complex sequence ofsetpcioperations does what you think it should do.
- Showsetpciversion. This option should be used stand-alone.
- Show detailed help on available options. This option should be used stand-alone.
- Show a list of all known PCI registers and capabilities. This option should beused stand-alone.
PCI access options
The PCI utilities use the PCI library to talk to PCI devices (seepcilib(7) for details). You can use the following options toinfluence its behavior:
- -A <method>
- The library supports a variety of methods to access the PCI hardware.By default, it uses the first access method available, but you can usethis option to override this decision. See -A help for a list ofavailable methods and their descriptions.
- -O <param>=<value>
- The behavior of the library is controlled by several named parameters.This option allows to set the value of any of the parameters. Use -O helpfor a list of known parameters and their default values.
- Use direct hardware access via Intel configuration mechanism 1.(This is a shorthand for -A intel-conf1.)
- Use direct hardware access via Intel configuration mechanism 2.(This is a shorthand for -A intel-conf2.)
- Increase debug level of the library.
Before each sequence of operations you need to select which devices you wish thatoperation to affect.
- -s [[[[<domain>]:]<bus>]:][<slot>][.[<func>]]
- Consider only devices in the specified domain (in case your machine has several host bridges,they can either share a common bus number space or each of them can address a PCI domainof its own; domains are numbered from 0 to ffff), bus (0 to ff), slot (0 to 1f) and function (0 to 7).Each component of the device address can be omitted or set to "*", both meaning "any value". All numbers arehexadecimal. E.g., "0:" means all devices on bus 0, "0" means all functions of device 0on any bus, "0.3" selects third function of device 0 on all buses and ".4" matches onlythe fourth function of each device.
- -d [<vendor>]:[<device>]
- Select devices with specified vendor and device ID. Both ID's are given inhexadecimal and may be omitted or given as "*", both meaning "any value".
When-sand-dare combined, only devices that match both criteria are selected. When multipleoptions of the same kind are specified, the rightmost one overrides the others.
There are two kinds of operations: reads and writes. To read a register, just specifyits name. Writes have the formname=value,value...where eachvalueis either a hexadecimal number or an expression of typedata:maskwhere bothdataandmaskare hexadecimal numbers. In the latter case, only the bits corresponding to binaryones in the mask are changed (technically, this is a read-modify-write operation).
There are several ways how to identity a register:
- Tell its address in hexadecimal.
- Spell its name. Setpci knows the names of all registers in the standard configurationheaders. Use `setpci --dumpregs' to get the complete list.See PCI bus specifications for the precise meaning of these registers or consultheader.h or /usr/include/pci/pci.h for a brief sketch.
- If the register is a part of a PCI capability, you can specify the name of thecapability to get the address of its first register. See the names starting with`CAP_' or `ECAP_' in the --dumpregs output.
- If the name of the capability is not known to setpci, you can refer to itby its number in the form CAPid or ECAPid, where id is the numericidentifier of the capability in hexadecimal.
- Each of the previous formats can be followed by +offset to add an offset(a hex number) to the address. This feature can be useful for addressing of registersliving within a capability, or to modify parts of standard registers.
- To choose how many bytes (1, 2, or 4) should be transferred, you should append a widthspecifier .B, .W, or .L. The width can be omitted if you arereferring to a register by its name and the width of the register is well known.
- Finally, if a capability exists multiple times you can choose which one to target using@number. Indexing starts at 0.
All names of registers and width specifiers are case-insensitive.
- asks for the word-sized command register.
- is a numeric address of the same register.
- asks for a 32-bit word starting at the location of the command register,i.e., the command and status registers together.
- specifies the upper byte of the vendor ID register (remember, PCI is little-endian).
- corresponds to the second word of the power management capability.
- asks for the first 32-bit word of the extended capability with ID 0x108.
The PCI Utilities are maintained by Martin Mares <mjAATTucw.cz>.
- General options
- PCI access options
- DEVICE SELECTION
- SEE ALSO
This document was created byman2html,using the manual pages.